Policies
Tier One Transmission's Core Return Policy
Tier One requires core returns for our built transmissions, valve bodies, and other parts. Many parts from other manufacturers also require core returns. In both cases, a refundable core charge will be assessed at the start of your order, which will be refunded once the OEM part that the new component replaces is returned, inspected, and accepted for a potential rebuild or remanufacture.
A "core" is defined as an OEM part or component that an aftermarket part will replace. For some products, cores need to be sent back to the manufacturer so that they can use them for other builds.
Tier One Transmission Core Return Process
When you order a complete, built transmission from Tier One, Tier One will send your new transmission with a return Bill of Lading. Please use the packaging and pallet used for your Tier One transmission to send your OEM transmission back to us with the included return Bill of Lading.Before sending your transmission to Tier One Transmissions please remove the following items from your transmission. They include but are not limited to:
- Shift Levers
- Cooler Fittings
- Speed Sensors
- External Temperature Sensor
- Neutral Safety Switch
- TTVA Motor etc.
- Vents and breather
Items found on the transmission when received by Tier One Transmissions are not the responsibility of Tier One Transmissions.
Once your OEM transmission core has been received by Tier One, we'll carefully inspect the transmission and its internal components. If the condition of your transmission core is deemed acceptable, Tier One will refund your core charge.
Tier One reserves the right to reject any core for any reason, including (but not limited to) the following reasons:
- Case damage or cracks
- Damaged or broken planetary gears
- Broken valve bodies or pumps
- Damaged or cracked torque converters
- Cracked or broken drums
- Cracked or broken pistons
- Cracked or broken accumulators
- Any other internal or external component damage
Any damage found may result in a partial or outright rejection of your core refund. Please allow 3-5 business days to complete your core inspection and refund.
Tier One Valve Body Core Return Process
When you order a Tier One Valve body, we require you to return your vehicle's OEM valve body as a core. You are responsible for arranging and paying for the return shipment. Please carefully package your OEM valve body using Tier One's valve body packaging and place the return label on the packaging.Once your core is packaged and labeled, take it to your shipping company of choice and return it to Tier One.
Tier One reserves the right to reject any valve body core for any reason, including (but not limited to) the following reasons:
- Damage or cracking on the valve body itself
- Collapsed or blocked channels
- Damaged or cracked plates
- Seized components that can't be removed without damage
- Any other internal or external component damage
Core Returns for Other Manufacturers
Other manufacturers may require core returns for their products (i.e. fuel injectors, turbochargers, fuel pumps, etc.). Each manufacturer has slightly different core return policies. However, manufacturers are not obligated to issue a full core refund, and your core may be rejected for any reason they see fit.Please allow up to 7-10 business days for your core return to be fully processed and refunded back to you.
If you've elected to have your shipping deducted from your core charge, you will not receive your full core charge back. If you have any questions or concerns about our core charge policies, contact us or call us directly at 602-399-5484!
Tier One's 2-Year Unlimited Mileage Transmission Warranty
Tier One Transmissions, LLC reserves the right to alter this warranty at any time. Warranty on parts installed by Tier One Transmissions, LLC falls back to the original manufacturer time/mileage periods and is solely up to the original manufacturer to honor. No warranty will be issued on existing transmission parts regardless of the core being supplied by Tier One Transmissions, LLC or the customer.
****IT IS YOUR RESPONSIBILITY TO READ ANY LITERATURE THAT MAY COME WITH YOUR TRANSMISSION OR OTHER COMPONENT REGARDING ADDITIONAL STEPS THAT MUST BE TAKEN IN ORDER FOR A PROPER INSTALLATION & FUNCTION OF THE UNIT.****
****It is the vehicle owner’s responsibility to ship transmission or vehicle to Tier One Transmissions, LLC location for any and all repairs needing to be performed. Any repairs to transmission not authorized by Tier One Transmissions, LLC will void warranty and will not be covered by Tier One Transmissions, LLC.****
PLEASE NOTE: IF YOU ARE INSTALLING A TRANSMISSION YOURSELF, IT IS YOUR RESPONSIBILITY TO HAVE THE TRANSMISSION COOLER FLUSHED BY A PROFESSIONAL PRIOR TO THE TRANSMISSION INSTALL. FAILURE TO DO SO, MAY RESULT IN CONTAMINATED FLUID AND OLD MATERIAL GETTING INTO THE NEW UNIT. POURING ATF THROUGH THE COOLER IS NOT SUFFICIENT ENOUGH. IF A PROPER HOT FLUSH IS NOT ABLE TO BE COMPLETED, THEN COMPLETE REPLACEMENT OF COOLER IS REQUIRED (WITH INVOICE/PHOTOS TO SUPPORT SENT BACK TO TIER ONE TRANSMISSIONS, LLC) AND KOOLER KLEEN USED FOR LINE FLUSH TO MAINTAIN WARRANTY.
Every transmission built by Tier One Transmissions, LLC must go through a proper break in procedure. You will be asked to review and sign this included procedure. Failure to properly break in a Tier One Transmissions, LLC built transmission will void the offered up to 2 year limited Nationwide warranty.
Craftsmanship/Labor warranty on a standard, automatic transmission build is 24 months including unlimited mileage for up to 700 HP. Over 700 HP will have a 1 year unlimited mile warranty. At our discretion, we may provide assistance with shipping and/or freight charges if the product is found to fall under warranty.
During the second year for transmissions 700 HP and below, Tier One Transmissions, LLC labor warranty on transmissions is solely up to Tier One Transmissions, LLC discretion to offer assistance.
Tier One Transmissions, LLC will not be held accountable for any towing, rental vehicle, travel/lodging or other outside expenses incurred due to any type of failures that may arise under this warranty.
Non-covered items would include broken transmission shafts and planetary/gear assemblies under any circumstances. Additionally, no assistance will be given for any items that are damaged as a result of said shaft or assembly. Low oil conditions will result in no warranty for transmission. Also, fluid contamination due to heat exchanger failure or other sources of water, coolant, etc. Incorrect transmission installation will result in no warranty for transmission. Transmission tuning that is found to not meet manufacturer’s and/or Tier One Transmissions, LLC recommendations will result in transmission warranty being denied.
Electrical components will only receive a 90 day warranty for any type of labor assistance.
Tier One Transmissions, LLC may assess a fee for transmission teardown and inspection if no warrantable item is found to have been the cause of failure. Any transmission failure that is the result of vehicle damages before transmission installation will be on the installer to cover transmission repair if said vehicle and/or outside circumstances cause the transmission to fail. Warranty work is solely at the discretion of Tier One Transmissions, LLC. Invoice number and all customer information will be filled out in full, including the Warranty Registration (within 30 days), the initial required pressure readings described on our website - model specific, proof of a professionally performed Hot Flush cooler cleaning or new cooler replacement (available at most neighborhood transmission repair facilities) entered into the Tier One Customer Portal, or no transmission warranty will be supplied by Tier One Transmissions, LLC. The original invoice date will be the start of the warranty. All required paperwork must be returned within 30 days of invoice date or warranty will be void.
Appropriate gear ratios:
It is the responsibility of the vehicle owner to ensure that the transmission has the proper tuning as transmission failure caused by inadequate or improper tuning will not be covered under warranty.
68RFE Appropriate gear ratios:
- 35" tire min gearing is 4:10
- 37" tire min gearing is 4:30
- Larger than that should be running a 4:56 ratio
**** MOST SHIPPING CARRIERS AND CONTRACTORS HAVE A STRICT POLICY THAT REQUIRES YOU TO INSPECT THE SHIPPED MERCHANDISE. FAILURE TO PROPERLY INSPECT AND THEN ACKNOWLEDGING WITH YOUR SIGNATURE THAT YOU ACCEPT THE ORDER MAKES YOU RESPONSIBLE FOR ANY DAMAGE CAUSED IN SHIPMENT. This is the policy of the shipping contractors and not the policy of Tier One Transmissions. We can assist in the freight claim if necessary, but they generally uphold their “signature policy”.****
Tier One's 2-Year/Unlimited Mileage Warranty does not apply to any transmission shipped outside of the United States, Canada, and Mexico. All overseas warranty issues will be handled on a case-by-case basis.
Tier One's Transmission Break-In Procedures & Policy
As referenced in the 2 year limited Nationwide warranty. Any transmission purchased from Tier One Transmissions, LLC will have a standard break in procedure that must be followed or transmission warranty could be denied.
Some transmissions may require a reflash, relearn or quick-learn procedure to operate properly and shift as they should before they can be driven. This is up to the customer to verify before moving any vehicle that may have a transmission built from Tier One Transmissions, LLC. All Allison 1000, 6L80, 6L90, 68RFE, 66RFE, 45RFE, 5R110W AND 6R140 require some type of procedure before they can be driven. If your transmission is not listed here, this does not mean your transmission does not require a procedure.
Transmission fluid specs must be at the correct level before the vehicle can be driven. Any transmission that is not correctly checked on fluid level can be denied on transmission warranty.
Every Transmission that is built by Tier One Transmissions, LLC must go through a 300 mile break in, no heavy driving or towing during break in is permitted until full break in procedure is completed. Transmissions must be driven under 25% or less throttle when performing transmission break in procedure. After the 300 miles has been completed the transmission cannot be run at full throttle until the secondary 100 mile learning process has been completed as the clutches will continue meshing together to seat properly, helping the overall integrity and longevity of your new transmission parts.
Several passes must be completed on the lowest power tune at 50% throttle until transmission shifts smoothly. Then transmission must be run at 75% throttle until transmission shifts smoothly. Then transmission can be run under full power and full throttle. Every transmission must have this break in procedure performed or transmission warranty will be denied.
If a transmission is found to not perform it is up to the purchaser to contact Tier One Transmissions, LLC to be advised on further instruction for the transmission. The purchaser or operator of any Tier One Transmissions, LLC transmission is required to take any necessary precaution that will prevent any further transmission damage. Any transmission that is confirmed to have been neglected will be subject to transmission warranty being denied.
Tier One Transmission's Freight Shipping Policy
Oversized and large items, including Tier One's built transmissions, ship via freight. Tier One's built transmissions have an additional $700 flat-rate shipping charge that covers both the shipment of your transmission and the shipping back of your core with our included return Bill of Lading. We do offer free freight shipping for other products on our site like lift kits, bumpers, complete suspension systems, oversized hitches, and other items. Freight shipments can have have at least a 1-3 business day prep time to arrange the shipping and palletization of your item or items.
When an item or items ship freight, it's extremely important to carefully inspect ALL items and/or boxes in the freight shipment for damage before signing the Bill of Lading while the delivery personnel are still on-site. Once you sign the Bill of Lading, the shipment is now yours, and you will not be able to return or reject the entire freight shipment. Please ensure that all items are free from damage. If an item/items in your freight shipment are damaged, immediately contact Tier One at 602-399-5484 for further instructions.
In the case that your item or items are so badly damaged that you freight shipment is rejected, we will work with you on a return, replacement, and/or refund as soon as the claim is processed with the freight service. Unfortunately, we cannot guarantee a specific time frame for claim processing.
Some products from some manufacturers may require the use of a lift gate for delivery to residential addresses. In these cases, additional charges may be applied.
Currently, we only offer international freight shipping to Canada and Mexico. If you are overseas in another country, but are interested in our products, please contact us directly for a quote. All international freight shipments may be subject to additional duties and taxes, and you and you alone are responsible for the payment of those duties and taxes.
For Tier One's own built transmissions, we can deduct the upfront shipping charge from the transmission's core charge to save you some money up front. However, you will get less money back from your initial core charge. Just select "Deduct from Core Charge" as your shipping option when you're ready to check out. If you have any questions about deducting your shipping from your core charge, contact Tier One or call us directly at 602-399-5484!
Tier One Transmissions Return Policy
Tier One offers a 30-day return policy on items ordered via phone or through Tier One's websites. Tier One reserves the right to reject any potential return for any reason at any time.
Return Process
To begin your return, please do the following:
- Log into your account on TierOneTransmissions.com and request a Return Merchandise Authorization (RMA) from your list of orders
- Fill out our RMA form with your reason(s) for the return
- Allow 3-5 business days for Tier One to process your return
- Follow Tier One's instructions for packaging and shipping
Once you ship your product back to Tier One, our supplier our warehouse, or our manufacturer, your item will be carefully inspected before a final decision on potential refunds, restocking fees, or outright rejection is assessed.
RMAs and returned items will be rejected for any or all of the following reasons:
- A package was sent without a valid and approved Tier One RMA
- The product was already installed
- The product was damaged by the user during an attempted install
- A different product is received than the one approved by the RMA
- The product is shipped back without its original packaging
- The product is missing hardware, manuals, or auxiliary parts needed for installation
Refunds
Once a product has been received, inspected, and accepted back into inventory, you will be issued a refund for the cost of your order. Tier One will not refund the following items, regardless of RMA rationale:- Shipping costs
- Installation costs
- Costs of rentals/vehicle downtime
- Taxes and duties for international shipping
- Any other real or perceived costs incurred due to a return
Tier One reserves the right to assess a 5-10% restocking fee on low-margin products, products with high shipping costs, or for any reason we deem necessary. However, both restocking fees and return shipping will be waived on approved RMAs that were the fault of a shipping carrier, Tier One, Tier One's suppliers, Tier One's 3PL warehouses, or Tier One's manufacturers.
Preparing your RMA Shipment
If your RMA is approved, Tier One will send you a return label that you'll need to place onto the original packaging of your item. Please ensure it's placed securely and in a clear place on the packaging in order to be seen by both the shipping carrier and our team at Tier One. Please also write your RMA number on the label in a clear place to ensure the quickest and most efficient processing of your return.Freight Shipping
Per Tier One's freight shipping policy, please inspect your ENTIRE freight shipment before signing the Bill of Lading. Once you sign the Bill of Lading, Tier One and the carrier are absolved of all responsibility for your freight shipment.If hidden damage is later uncovered, please contact Tier One directly for further instructions.
This return policy does not apply outside of the United States, Canada, and Mexico. All potential overseas returns will be handled on a case-by-case basis.
Tier One Transmission Installation & Tuning Notes
INSTALL GUIDE
- When using Billet flex-plate DO NOT use factory spacer.
- WIRE HARNESSES must inspected and repaired.
- Red loc-tite on converter and flex-plate bolts.
- All transmissions REQUIRE a cooler flush or complete cooler replacement before starting of the engine after transmission replacement.
- Oil levels must be at appropriate level when hot or cold.
- All six speed and up transmission/valve bodies require a RELEARN/ADAPT/KAM RESET after installation.
- Please attach serial number somewhere on your customers invoice – serial number for the trans is the invoice number that we give you. This will help us quickly identify the build in our system in case of warranty issues with the transmission.
- Complete all break in procedure forms and warranty forms and either email them to sales@tieronetransmissions.com or drop them off at our shop to be filed away within 30 days.
- Completing all warranty forms and returning them to Tier One is the responsibility of the installer. Warranty forms not completed/returned within 30 days will void the warranty.
LINE PRESSURE GUIDES
These numbers are needed for warranty info!47RE
- Line pressure in gear while at idle will be 75psi.
- Max line pressure under full throttle 1-3 will be 115psi.
- 145-160psi in OD and lock up.
- Line pressure in gear while at idle will be 80psi.
- Max line pressure under full throttle 1-3 will be 125psi.
- 160-190psi in OD and lock up.
- Max line pressure during road test – High pressure VB needs to be at 225psi at 25-30% throttle angle.
- Stock VB are 160psi.
- Line pressure in reverse should reach 250psi.
- Use of factory lock strategy must be used or transmission damage will occur.
- 2019 and up should have UD pulse turned off (Please verify on 2017 and 2018 Rams as some are equipped with this option).
- This transmission is designed to run with factory tuning or PPEI.
- You must complete the transmission relearn procedure until it is successful. Failure to complete a successful relearn will result in transmission failure.
- Line pressure at idle in gear should be 70-80psi.
- Line pressure at max throttle will be 250-325 depending on build level of transmission.
- Lock up pressure will vent about 40psi from max lock up when applied.
- Requires strategy relearn for valve body – code for strategy relearn is on the invoice.
- Must have factory transmission tuning.
- Requires strategy relearn and factory transmission tuning.
- Must have gear ratio updated per tire size of the vehicle if larger tires are used.
- Must have gear ratio updated per tire size of the vehicle if larger tires are used.
- For the 10L1000: We recommend Duramax Tuner and PPEI as approved transmission tuning sources.
- 10L1000 Tuning Advisory: Please be aware that we mechanically increase line pressure. Software increasing line pressure will cause issues for the transmission.
- Cylinder deactivation/displacement on demand (DOD) must be disabled.
- All L/U slip tables set to 0 rpm of slip.
- L/U apply disabled 1st-4th gear.
- Shift scheduling adjusted for tire size.
- 5-6 shift delayed 10% at below 25% throttle (after shift scheduling adjustment).
- TCC desired pressure set to a minimum of 30psi.
- TCC apply pressure ramp +20psi above 0 rpm slip.