Break In Procedure
Tier One Transmission Break-In Procedure
Built for Performance. Broken In for Reliability.
Your new Tier One transmission was built to handle the demands of your truck. Whether you're daily driving, towing heavy loads, or pushing serious horsepower, the first few hundred miles are important.
Every Tier One transmission requires a 300-mile initial break-in, followed by a 100-mile progressive learning period and a mandatory fluid change at 500 miles.
Following these instructions helps your transmission adapt to its new components and operating pressures, and gives you the opportunity to identify any installation or operating issues before putting the transmission under heavy load.
Step 1: Before Your First Drive
Before driving your truck, make sure the following have been completed:
-
Verify transmission fluid: Use the correct fluid specified for your transmission. Check the level using the proper manufacturer procedure and operating temperature.
-
Inspect the cooling system: Transmission cooler lines and coolers must be properly cleaned, flushed, or replaced as required to prevent contamination.
-
Check for leaks: Inspect all transmission connections, lines, fittings, and seals.
-
Complete required programming: Some transmissions require a reflash, quick-learn, adaptive reset, or other programming procedure before driving.
-
Verify operation: Confirm the transmission engages correctly and that there are no unresolved transmission-related diagnostic trouble codes.
Important: Some transmission applications require model-specific programming and relearn procedures. Always verify the correct requirements for your transmission before driving.
Step 2: Initial Break-In — First 300 Miles
Keep throttle at 25% or less.
During the first 300 miles:
-
Drive conservatively with light acceleration.
-
Include normal stop-and-go driving to allow the transmission to shift through its operating ranges.
-
Avoid hard acceleration, full-throttle pulls, and boosted launches.
-
Do not tow or haul heavy loads.
-
Avoid burnouts, racing, and dyno pulls.
-
Monitor transmission temperature and shifting behavior.
Some changes in shift feel can occur during this period, but persistent slipping, flaring, overheating, or abnormal noises should never be ignored.
Step 3: Progressive Learning — Miles 300–400
Once the initial 300 miles are complete and the transmission is operating correctly, begin the secondary learning process.
Using the lowest approved power setting:
-
Make several controlled accelerations at approximately 50% throttle, allowing the transmission to shift smoothly.
-
Once shifts are consistently smooth and normal, gradually increase to approximately 75% throttle.
-
Continue controlled driving until the transmission shifts consistently under the increased load.
Do not move to a higher throttle level if the transmission is slipping, flaring, overheating, or showing abnormal behavior.
Full-throttle operation is permitted only after the entire break-in and progressive learning procedure has been successfully completed.
Step 4: Required Break-In Fluid Change — 500 Miles
A transmission fluid change is mandatory at 500 miles following installation.
This initial service is an important part of the break-in process. New clutch materials and internal components can generate small amounts of break-in debris during initial operation. Changing the fluid helps remove accumulated contaminants and provides an opportunity to inspect the transmission for potential concerns.
At 500 miles:
-
Drain and replace the transmission fluid with the correct fluid for your application.
-
Replace or service the transmission filters as applicable.
-
Inspect the transmission pan and magnets for abnormal debris.
-
Inspect for leaks and verify proper operation.
-
Check and adjust fluid level according to the correct operating temperature and manufacturer procedure.
Keep your service receipt and mileage documentation for warranty records.
Step 5: Ongoing Transmission Maintenance
Once the initial 500-mile service has been completed, regular transmission maintenance is essential to long-term reliability.
Tier One recommends changing your transmission fluid every 20,000–30,000 miles following the initial break-in service.
Maintenance should include:
-
Transmission fluid replacement.
-
Filter replacement or service as applicable.
-
Inspection of the transmission pan and magnets.
-
Inspection for leaks and abnormal wear.
-
Verification of proper fluid level and transmission operation.
Trucks used for heavy towing, racing, high-horsepower applications, or other severe-duty conditions may require more frequent maintenance.
Regular servicing helps control contamination, maintain fluid performance, and identify developing issues before they result in costly repairs.
What If Something Doesn't Feel Right?
Stop and contact Tier One before continuing to drive.
If you experience slipping, harsh or inconsistent shifting, delayed engagement, unusual noises, overheating, or warning lights, do not continue driving in an attempt to complete the break-in.
Continuing to operate a transmission with a known problem can cause additional damage.
Our team is here to help diagnose the issue and determine the appropriate next steps.
Break-In & Warranty Requirements
Following Tier One's applicable installation, programming, fluid, break-in, and maintenance requirements is a condition of our limited transmission warranty.
The initial 500-mile fluid service is required. Retain documentation showing the service date, mileage, and work performed.
Failure to follow required procedures may affect warranty coverage in accordance with the written warranty terms.
Please review the complete Tier One warranty documentation for applicable conditions, exclusions, and claims procedures.
Questions about your transmission or break-in procedure? Contact Tier One Transmissions before proceeding.
Tier One and Done.